AASHTO T285 Test Fixtures & Test Systems
StandardsThe Mandrel-to-Die Ratio: Under AASHTO T285, the strain on the outer fibers is strictly controlled by the plunger radius. A…
Testing Equipment
Browse our full catalogue of industrial testing equipment. Use the filters to narrow results by test type, sample standard, or force capacity.
627 items found
-
-
ADIDAS ST-05 Test Fixtures & Test Systems
StandardsStrain Accuracy in Polymers: For ADIDAS ST-05, the precision of the Class B-1 calibration is paramount. In footwear material testing,…
-
AFERA 5001 Test Fixtures & Test Systems
StandardsPeel Table Kinematics: AFERA 5001 requires a highly controlled 90° or 180° peel environment. Our precision peel tables utilize low-friction…
-
AITM 1-0010 Test Fixtures & Test Systems
StandardsCAI Rigidity: This Airbus method determines residual compressive strength after Barely Visible Impact Damage (BVID). The fixture must provide anti-buckling…
-
AITM 1-0076 Test Fixtures & Test Systems
StandardsHigh-cycle fatigue (HCF) at 15.9k cycles/hour requires active temperature monitoring to avoid hysteretic heating.
-
ANSI A118.1 Test Fixtures & Test Systems
StandardsMaintain salt solution pH between 6.5 and 7.2 to prevent skewed galvanic corrosion rates during the 534-hour soak.
-
API 5L Test Fixtures & Test Systems
StandardsThe Percent Shear on the fracture surface is the primary metric for pipeline crack arrest capability.
-
AS 2205 Test Fixtures & Test Systems
StandardsCalibrate against NIST-traceable secondary standards (FN) before and after each shift to ensure magnetic accuracy.
-
ASME IX Test Fixtures & Test Systems
StandardsThe Root of the Matter: Cross-sectional analysis must target the start/stop points of the weld run. These are the highest-risk…
-
ASTM A185 Test Fixtures & Test Systems
StandardsYield Point Capture: Low-carbon steel exhibits distinct Lüders bands; use a low strain rate (0.005 in/in/min) to prevent overshooting the…
-
ASTM A262 Test Fixtures & Test Systems
StandardsSensitization Screening: This electrolytic oxalic acid etch is a Go/No-Go test. A Ditch structure indicates the steel is susceptible to…
-
ASTM A370 Test Fixtures & Test Systems
StandardsViscoelastic Creep: In polymer-lined piping, the hardness value will drop the longer the needle is held. Standardized Dwell Time is…
-
ASTM A370 Test Fixtures & Test Systems
StandardsSub-Size Normalization: Always normalize energy values (J/cm2) when comparing 5mm sub-size specimens to 10mm full-size bars to avoid underestimating fracture…
-
ASTM A370 Test Fixtures & Test Systems
Standards885F Embrittlement Zone: Use a 10mm carbide ball with a 3000kg load; ensure the surface is ground flat and parallel…
-
ASTM A370 Test Fixtures & Test Systems
StandardsZ-Direction Integrity: Use a 0.250 inch diameter reduced section to check for lamellar tearing susceptibility in structural plates.
-
ASTM A497 Test Fixtures & Test Systems
StandardsNotch Sharpness: The fatigue crack starter-notch must be sharp enough to prevent overestimating the toughness value (KIc); a blunt notch…
-
ASTM A720 Test Fixtures & Test Systems
StandardsASTM A720 (Hydrogen Embrrit.)
-
ASTM A974 Test Fixtures & Test Systems
StandardsWeld Shear Uniformity: This standard is the life-safety check for gabions. The fixture must isolate the weld joint to ensure…
-
ASTM B312 Test Fixtures & Test Systems
StandardsPowder Compact Integrity: Green Strength is a measure of the cold-weld bond between metal powder particles. The fixture must provide…
-
ASTM B406 Test Fixtures & Test Systems
StandardsTransverse Rupture (TRS): Hardmetals (Tungsten Carbide) are incredibly brittle. Any non-parallelism in the fixture will cause a catastrophic twist failure…